ATLS Whole House Air Purifier ATLS-STUV36 Model - HVAC Air Purifier

Name: Atlas whole House HVAC Air Purifier ATLS-STUV36
SKU: ATLS-STUV36
Price: 209.9900 USD
Availability: InStock

The ATLS-STUV36 HVAC air purifier model is a powerful UVC unit that is recommended for purifying alergies like sinus, mold, allergies, bacteria, headaches, influenza, bronchitis and household odors. The air system in this unit is1-5 tons and is capable of killing up to 99.9% of existing viruses and prevents these contaminants like mold, mildew and airborne viruses and will prevent them from ever growing again and spreading.

Description:
This unit comes with an electonic ballast (Advance Purevolt Electronic Ballasts -Featuring Intellivolt / EOL Protection) and an indicator LED. The bulbs are germicidal UVC and they are 99% efficent on a single pass. The installation is super easy and straight forward and comes with instruction manual and hardware.This Atlas ATLS-STUV36 covers up to 1500 sqft

Features:

This unit has a UVC Germicidal lamps are scientifically proven to kill 99.9% of airborne germs. This latest model of air purifier is a total home purifier, air sanitizers that utilizes dual 254nm lamps which are easily placed in the intake side of your existing heating/cooling system or directly above the AC coil.

Features:

Proven to kill 99.9% of airborne germs
Home purifier
Air Sanitizers
Single 254nm dual tube lamp
No Ozone
Installation takes less than 15 minutes
1 year limited manufacturer warranty

1-Year Limited Manufacturer's Warranty

Specifications:

Model ST-UV36
13000 hours UV bulb lifetime
254 NM UVC
36 W power
HVAC systems and indoors
110V or 220V Voltage
Work within 1500 sqft
Bulb diameter: 17mm, length 411 mm
254*160*56 mm Base
475*260*125 mm dimensions
1.5 KG Net Weight
2.2 KG Gross weight

Installation:

PLEAE NOTE: PROFFESIONAL INSTALLER IS REQUIRED FOR INSTALLING THIS DEVICE
CAUTION: BE SURE TO WEAR APPROPRIATE PROTECTION AS CUTTING METAL IS LOUD AND PIECESMAY BE SHARP AND HOT (I.E. HAND, EAR, EYE, AND FACEPROTECTION)

Disconnect power to the HVAC system before installing the unit.
Need to create a template and tape it to the duct work in the intended installation position.
Drill pilot holes as required with a 3/32” drill bit.
Cut out the appropriate hole on the HVAC pannel.
Remove any burrs and be sure duct surface is flat after cutting the hole(s).
Install the bulb(s) in the unit by sliding the bulb in from the outside until the bulb snaps into place. Insert the unit into the metal duct cut out. If you touch the bulb with your hands, use a cloth to wipe any fingerprints from the bulb(s).
Attach the unit to duct work with the supplied 4 sheet metal screws using a ¼” nut driver. Make sure to tighten screws evenly. The unit has a factory installed gasket that ensures a tight seal between the unit and the duct work. Be sure the unit is flat against the duct work on all sides. CAUTION: DO NOT OVERTIGHTEN SCREWS.
Plug the unit into a grounded 120 volt power outlet.
Turn unit on and verify that the LED indicator light(s) located near the on/off switch is/are illuminated.
The switch is in the on position when the solid line on the switch is pressed down.
Reconnect the power to the HVAC system
The unit is now operational and does not need to be powered off unless cleaning or bulb replacement is necessary

Note: NEVER LOOK DIRECTLY AT OR TOUCH A UV BULB WHILE ILLUMINATED.

UPC: 859456003093
SKU: ATLS-STUV36